- #FUJITSU 16LX PROGRAMMER INSTALL#
- #FUJITSU 16LX PROGRAMMER SERIAL#
- #FUJITSU 16LX PROGRAMMER DRIVER#
- #FUJITSU 16LX PROGRAMMER MANUAL#
- #FUJITSU 16LX PROGRAMMER SOFTWARE#
Note that the install might not be performed when a directory in a deep nest is specified as the install directory.Īfter installation, click the Windows Start button => Program => FUJITSU FLASH MCU Programmer => FMC16FX to start the programmer software.Įrase, Blank Check, Program & Verify, Read & Compare, and Copy can be executed for flash memory integrated into the microcontroller. Starting the installer to operate as instructed will complete the installation.
#FUJITSU 16LX PROGRAMMER SOFTWARE#
If the old software version is installed, uninstall it first before installation. Minimum values of setup and hold times of each signal on rising edge of RSTXĦ. Input data to each pin of the microcontroller with the following timing on the basis of the input of the RSTX pin. 3*: The user can select one channel of UART2 or 3. 2*: The user can select one channel of UART0-1 or 2.
#FUJITSU 16LX PROGRAMMER SERIAL#
Type Serial Data Input Pin Serial Data Output Pin Supply Voltage (2) Serial data I/O pins for each type of microcontroller SOT Note that the pin varies with the type of microcontroller. Pin SIN Note that the pin varies with the type of microcontroller. Reset pin RSTX Cancel reset after setting Mode pins to the flash reprogramming mode.
When MD2 and MD0 are set to L and MD1 is set to H, they enter the reprogramming mode. Should be controlled in flash memory reprogramming mode. PINS USED FOR ON-BOARD REPROGRAMMING (1) Control pins for on-board programming *1: Check the settings of the serial data input/output pins used in each microcontroller.Ĥ.
#FUJITSU 16LX PROGRAMMER MANUAL#
When programming data to mass-produced products using the Yokogawa Digital Computer serial programmer some time in the future, it is best to generate the patterns for serial clock pins on the printed circuit board according to the connection example for serial programming described in the Hardware Manual for each microcontroller. Note: The port numbers of the SIN and SOT pins vary with the types of microcontrollers. Then RSTX pin set from Low to High level executes user program. When the RSTX pin is set from Low to High level after setting the MD2, MD1, MD0 pins, the microcontroller enters the serial reprogramming mode, enabling serial reprogramming from the PC.Īfter the reprogramming, control is shifted to the normally-used mode as for MD2, MD1 and MD0 pins. The MD2, MD1, MD0 pins cannot be controlled by the PC and should be set in the user system. EXAMPLE OF CONNECTION FOR ON-BOARD REPROGRAMMING BY PROGRAMMER
#FUJITSU 16LX PROGRAMMER DRIVER#
Note that the user system must have an RS-232C driver for communication with the microcontroller UART. Using RS-232C cable connected to the personal computer (Windows PC), flash memory data in the microcontroller mounted in the user system can be reprogrammed. 18įUJITSU FLASH MCU Programmer for F2MC-16FX Specifications Programmer Functions.7ħ.1 Downloading.8 7.2 Erasing and Programming.10 7.3 Internal motorola S decoder specification.12 7.4 Special specification. Example of Connection for On-board Reprogramming by Programmer.
Internal motorola S decoder specifiction is added.ġ. Serial data I/O pins for MB96F326A/R/Y is corrected. If the products and technologies described in this document are controlled by the Foreign Exchange and Foreign Trade Control Act established in Japan, their export is subject to prior approval based on the said act. For such applications, contact your Fujitsu sales representative.ħ.
The products described in this document are not intended for use in equipment requiring high reliability, such as marine relays and medical life-support systems. No part of this publication may be copied or reproduced in any form or by any means, or transferred to any third party without prior written consent of Fujitsu.Ħ. Fujitsu reserved the right to change products or specifications without notice.ĥ. The information contained in this document does not convey any license under the copy right, patent right to trademarks claimed and owned by Fujitsu.Ĥ. However, Fujitsu assumes no responsibility for inaccuracies.ģ. The information contained in this document has been carefully checked and is believed to be reliable. Complete information sufficient for construction proposes is not necessarily given.Ģ. Circuit diagrams utilizing Fujitsu products are included as a mean of illustrating typical semiconductor applications. Version 1.03 26 March 2008 Software version: V01L04Ģ007-2008 FUJITSU LIMITED Printed in Japanġ. MCU Programmer for F2MC-16FX Specifications
0 kommentar(er)
